T5120/T5220の転用

NW管理用のサーバを探していたら、T5120というサーバをもらうことができました。

まずは、蓋を開けます。

電源|バス|バス|バス

中央のバス一番おくまったところに JP6801というジャンパーがあるのでピンをショートさせます。

ciscoのロールオーバーケーブルをSER MGTという緑ラベルのポートにさしてteratermを立ち上げます。

電源を入れて、ILOMが立ち上がって login:と出てきたところで、おもむろにピンのショートを解除します。

root / changeme でログインします。

★電源on
->  55 AA T2 T3 T4
POST memory PASSED
FLASH: 32 MB
In:    serial
Out:   serial
Err:   serial
Net:   FEC ETHERNET
POST i2c  c  d 18 20 2a 2d 2e 30 40 43 46 51 53 54 56 68 69 6a 6b 70 71 PASSED
POST cpu PASSED
POST ethernet PASSED
Booting linux in 5 seconds…
## Booting image at fe080000 …
   Image Name:   Linux-2.4.22
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    814989 Bytes = 795.9 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum … OK
   Uncompressing Kernel Image … OK
do_bootm_linux():
  argv[0]=bootm
  argv[1]=0xfe080000
## Current stack ends at 0x03D38B70 => set upper limit to 0x00800000
No initrd
## cmdline at 0x007FFF00 … 0x007FFF80
memstart    = 0x00000000
memsize     = 0x04000000
flashstart  = 0xFE000000
flashsize   = 0x02000000
flashoffset = 0x0004C000
sramstart   = 0x00000000
sramsize    = 0x00000000
EnvAddr     = 0xCEB7CC31
EnvSize     = 0xCC31CCB3
sectorsize  = 0x00020000
sectorcount = 0x00000100
booted      = 0xFE080000
boottype    = 0x00000000
primary     = 0xFFFFFFFF
pritype     = 0x00000000
secondary   = 0xFFFFFFFF
sectype     = 0x00000000
image0      = 0xFE000000
image1      = 0xFF000000
maximage    = 0x01000000
immr_base   = 0xF0000000
bootflags   = 0x00000001
intfreq     =    133 MHz
busfreq     = 66.500 MHz
ethaddr     = 00:21:28:13:56:F1
IP addr     = 0.0.0.0
baudrate    =   9600 bps
## Transferring control to Linux (at address 00000000) …
## parameters(007ffe90,00000000,00000000,007fff00,007fff80)
Linux version 2.4.22 (kbellew@sanpen-rh5-1) (gcc version 3.3.4) #2 Mon Sep 15 16:22:50 PDT 2008 r36965
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock4 rootfstype=squashfs ro mtdparts=phys:384K(u1),128k(e1),1536K(k1),14M(r1),384K(u2),128K(e2),1536K(k2),14M(r2)
Decrementer Frequency = 498750000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Calibrating delay loop… 132.71 BogoMIPS
Memory: 62828k available (1416k kernel code, 444k data, 68k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
CPM UART driver version 0.03
ttyS00 at 0x0100 is apty: 256 Unix98 ptys configured
Generic RTC Driver v1.07
eth0: FEC ENET Version 0.2, FEC irq 3, MII irq 6, addr 00:21:28:**:**:**
RAMDISK driver initialized: 16 RAM disks of 18432K size 1024 blocksize
eth0: Phy @ 0x0, type DM9161 (0x0181b881)
loop: loaded (max 8 devices)
physmap flash device: 2000000 at fe000000
 Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Using command line partition definition
Creating 8 MTD partitions on “Physically mapped flash”:
mtdblock1: 0x00000000-0x00060000 : “u1”
mtdblock2: 0x00060000-0x00080000 : “e1”
mtdblock3: 0x00080000-0x00200000 : “k1”
mtdblock4: 0x00200000-0x01000000 : “r1”
mtdblock5: 0x01000000-0x01060000 : “u2”
mtdblock6: 0x01060000-0x01080000 : “e2”
mtdblock7: 0x01080000-0x01200000 : “k2”
mtdblock8: 0x01200000-0x02000000 : “r2”
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-rpx.o: i2c MPC8xx module version 2.6.1 (20010830)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
ip_conntrack version 2.1 (512 buckets, 4096 max) – 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 68k init
modprobe: modprobe: Can’t open dependencies file /lib/modules/2.4.22/modules.dep (No such file or directory)
Creating /var tmpfsCreating directories in /var …done.
Creating /var/log tmpfsdone.
Activating swap.
Calculating module dependencies… done.
Loading modules: fpga Warning: loading /lib/modules/2.4.22/misc/fpga/fpga.o will taint the kernel: non-GPL license – Proprietary
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Platform ID      : 1
Minor revision   : 0
Major revision   : 5
FPGA power status : 80
  (SYS_POK_EN  !DC_POK  !POK_OIO  !POK_VMEMR  !POK_VMEML  !POK_VCORE  !POK_PSU1  !POK_PSU0 )
BR2: 0xf2000000/0x1000000/0xf2000401/0xff0001fc
FPGA init OK: base f2000000, size 1000000 (major 120)
Module fpga loaded, with warnings
fpga_flash Warning: loading /lib/modules/2.4.22/misc/fpga_flash/fpga_flash.o will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module fpga_flash loaded, with warnings
immap Warning: loading /lib/modules/2.4.22/misc/immap/immap.o will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module immap loaded, with warnings

Checking all file systems…
fsck 1.37 (21-Mar-2005)
Setting kernel variables …
kernel.core_pattern = /coredump/%h.%e.core
kernel.core_uses_pid = 1
net.ipv4.ip_local_port_range = 3100 7075
… done.
Mounting local filesystems…
Cleaning /tmp /var/run /var/lock.
Identifying DOC Device Type(G3/G4/H3) …

Using /lib/modules/2.4.22/misc/tffs/tffs_h3.o
tffs: TrueFFS driver 7100.76
tffs: will not use IRQ
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=8.
tffs: Flow: G4_docWindowBaseAddress Exit (NOT FOUND).
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=8.
tffs: Looking for H1 DOC at address 0xc9156000
tffs: DOCH found
tffs: Socket 0 in addr 0xf4000000
tffs: Device 0x0: size 0x76c0000 HW sector 0x200 (recommended 0x1000)
tffs: use major device number 100
Partition check:
 tffsa: tffsa1 tffsa2 tffsa3
tffs:     disk partition: dev_number=0x6401, 65534 sectors, start_sector=1
tffs:     disk partition: dev_number=0x6402, 65536 sectors, start_sector=65535
tffs:     disk partition: dev_number=0x6403, 112000 sectors, start_sector=131071
Loaded TFFS kernel module /lib/modules/2.4.22/misc/tffs/tffs_h3.o
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,0), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,3), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Checking DOC size…
Mounted all disk partitions.

Setting the System Clock using the Hardware Clock as reference…
System Clock set. Local time: Fri Mar 31 04:56:12 GMT 2017

Setting up networking…done.
Running ldconfig…done
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces…eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
done.
Hostname: SUNSP00**********.
Starting portmap daemon: portmap.
Initializing random number generator…done.
INIT: Entering runlevel: 3
Starting system log daemon: syslogd and klogd.
Starting periodic command scheduler: cron.
Starting IPMI Stack…… Done.
Starting portmap daemon: portmap.
Starting OpenBSD Secure Shell server: sshd.
Starting Servicetags discoverer: stdiscoverer.
Starting Servicetags listener: stlistener.
Starting FRU update program: frutool.

SUNSP00********** login:

★ILOMへのログイン

SUNSP00********** login: root
Password: changeme          ★エコーバックはありません。
Waiting for daemons to initialize…

Daemons ready

Sun(TM) Integrated Lights Out Manager

Version 2.0.4.26.d

Copyright 2008 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Third-party software, including font technology, is copyrighted and licensed
from Sun suppliers.
Portions may be derived from Berkeley BSD systems, licensed from U. of CA.
Sun, Sun Microsystems, and the Sun Logo are trademarks or registered trademarks
of Sun Microsystems, Inc. in the U.S. and other countries.

Federal Acquisitions: Commercial Software — Government Users Subject to
Standard License Terms and Conditions.

Copyright 2008 Sun Microsystems, Inc. Tous droits r辿serv辿s.
Distribu辿 par des licences qui en restreignent l’utilisation.
Le logiciel d辿tenu par des tiers, et qui comprend la technologie relative
aux polices de caract竪res, est prot辿g辿 par un copyright et licenci辿 par
des fournisseurs de Sun.
Des parties de ce produit pourront 棚tre d辿riv辿es des syst竪mes Berkeley BSD
licenci辿s par l’Universit辿 de Californie.
Sun, Sun Microsystems, et le logo Sun sont des marques de fabrique ou des
marques d辿pos辿es de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays.

Warning: password is set to factory default.  ★パスワードがデフォルト(root/changeme)になりましたといふメッセージ

-> stop /SYS
Are you sure you want to stop /SYS (y/n)? y
stop: Target already stopped

-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS

-> start /SP/console
Are you sure you want to start /SP/console (y/n)? y

Serial console started.  To stop, type #.
Done
0:0:0>Master CPU Tests Basic….Done
0:0:0>Init MMU…..
0:0:0>NCU Setup and PIU link train….Done
0:0:0>L2 Tests….Done
0:0:0>Extended CPU Tests….Done
0:0:0>Scrub Memory….Done
0:0:0>SPU CWQ Tests…Done
0:0:0>MAU Tests…Done
0:0:0>Network Interface Unit Tests….Done
0:0:0>Functional CPU Tests….Done
0:0:0>Extended Memory Tests….Done
2017-03-31 05:09:21.635 0:0:0>INFO:
2017-03-31 05:09:21.641 0:0:0>  POST Passed all devices.
2017-03-31 05:09:21.649 0:0:0>POST:     Return to VBSC.
2017-03-31 05:09:21.656 0:0:0>Master set ACK for vbsc runpost command and spin…
|

SPARC Enterprise T5220, No Keyboard
Copyright 2008 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.29.0.a, 8064 MB memory available, Serial #85******.
Ethernet address 0:21:28:**:**:**, Host ID: 85******.

{0} ok

★OK Prompt